Selection
How to choose an extrusion blow molding machine: five decisions in order
Most bad machine purchases come from choosing the machine before the container. These are the five decisions that fix the specification, in the order they have to be made.
1. Start from the container, not the machine
Write down four numbers before you talk to any supplier: the volume, the weight, the neck finish and the output per shift. Everything else in the specification follows from those four.
Volume sets the platform. Weight sets the screw and the cooling. Neck finish sets the die head and the blow pin. Output sets the cavity count — which is where most first-time buyers make their mistake, because they assume a bigger machine gives more output. It does not. Cavities give output; the machine only has to be big enough not to limit them.
| What you know | What it decides |
|---|---|
| Container volume | Platform size (which model family) |
| Container weight | Screw diameter, plasticising capacity, cooling time |
| Neck finish and diameter | Die head spacing, blow pin, mold neck insert |
| Output per hour or per shift | Cavity count, and with it the die head count |
| Material and layer structure | Number of extruders, die head type |
2. Decide the layer structure before the machine size
Single layer, three layer or five layer changes the machine far more than one platform size does. A three-layer machine carries three extruders and a die head that keeps three melt streams concentric; that is a different machine, not an option on the same one.
The reason to go multilayer is rarely appearance. It is to put regrind in the middle layer so the visible and food-contact surfaces stay virgin, or to add a barrier resin that the single-layer wall cannot hold. If neither applies, single layer is the cheaper and simpler choice.
3. Size the screw from the heaviest container, the cavities from the lightest
These two limits pull in opposite directions, and this is the step buyers most often skip.
- The screw is sized by the heaviest container. Work out kilograms per hour at the target cycle: containers per hour multiplied by container weight, with an allowance of about 1.4 for flash and scrap. If that number is above the screw’s plasticising capacity, the machine will run short of melt and the cycle will drift.
- The cavities are sized by the lightest container and the target output. A 2 g container at 2,000 per hour is 4 kg/h — trivial for the screw, but it still needs enough cavities to hit 2,000 an hour at a realistic cycle.
A machine that satisfies both is the right size. A machine that satisfies only one is the machine you will regret buying.
4. Choose single or double station
Double station runs two molds alternately: one is blowing while the other is opened, emptied and reloaded. It roughly doubles output for the same footprint and the same die head, at a price premium and with more moving parts.
| Single station | Double station | |
|---|---|---|
| Molds on the machine | 1 | 2 |
| Containers per cycle | Die head count × 1 | Die head count × 2 |
| Mold change | One mold to change | Two molds to change |
| Best for | Frequent mold changes, low volume, large containers | Long runs of one container, high volume |
Rule of thumb: if you change molds more than once a week, single station loses less time. If you run one or two containers for months, double station wins on cost per thousand.
5. Choose the options by what they replace, not by what they add
Every option on a blow molding line replaces a labour cost or a reject rate. That is the only way to judge it.
| Option | What it replaces | When it pays |
|---|---|---|
| Automatic de-flashing | One operator trimming necks by hand | Any container where the neck is a sealing surface |
| Parison wall thickness control | Manual die adjustment and high scrap | Four cavities and above, or containers over 5 L |
| Leak tester | Returns and rework after filling | Containers that hold liquid under pressure or must not weep |
| Conveyor and take-out | Someone walking bottles to the packing table | Always, once output passes a few hundred an hour |
| Chiller | Cycle time drifting with the weather | Anywhere the water temperature is not controlled |
| Granulator and loader | Selling scrap by weight instead of reusing it | Any line producing flash |
The one-page specification
Before requesting a quotation, you should be able to fill in every line below. If a line is blank, the quotation will be a guess.
- Container: volume, weight, height, diameter, neck finish
- Material: resin, grade, layer structure, regrind percentage
- Output: containers per hour, or per shift, and the hours per day
- Cavities: required, or let the supplier calculate from your output
- Station: single or double
- Options: de-flashing, wall thickness control, leak test, conveyor, chiller, granulator
- Utilities available: voltage, phase, frequency, compressed air, cooling water
Where to go next
- Twenty buyer questions — the short answers to the questions this article raises
- Engineering reference: three machines instead of one — the five decisions applied to a 250 ml to 5 L range
- All nine KSY models side by side — screw, cavities and container range in one table
- Single or double station clamping — the decision that doubles output and a quarter of the price
- How to calculate output — the three formulas behind every capacity figure
- Containers our machines make — start from the container and work back to the machine
Need a machine sized for your container?
Send the container size, weight, material and the output you need. We answer with a machine proposal and a capacity calculation, not a catalogue.