PHILIPPINES
5 L detergent bottles and 1.8 L view-strip bottles in the Philippines
A detergent range from 5 L down to 1.8 L across four machine specifications, each chosen for a different problem: parison weight at the top, strip clarity in the middle, and the cavities a short cycle can carry.
Project at a glance
| Country | Philippines |
|---|---|
| Industry | Household detergent and food packaging |
| Containers | 5 L detergent bottles; 1.8 L bottles with a clear view strip; 2.5 L bottles |
| Machines | KSY75-J6L, KSY50-J2L × 2, KSY55-J2.5L, double station |
| Cavities | Two per cycle on the single-head machines, four on the two-head machine |
| Construction | Single layer, HDPE and PVC |
| Electrical | 380 V, 50 Hz, three phase |
Engineering reference. Configuration from a project our engineers worked on, restated with the equivalent current KSY models; where the original project used a single-station machine, the current KSY equivalent is double-station. Cycle times and hourly output are for reference only: the exact output depends on your container, above all its weight.


A 5 L bottle is a weight problem
The 5 L pack is not hard because it is large. It is hard because of what hangs off the die head before the mold closes: a 5 L parison is heavy and long, and it stretches under its own weight in the second between extrusion and clamp. Two heads make that worse: a wider die head, a longer transfer, and a small temperature difference between the parisons becoming a wall difference between two bottles.
One head keeps the parison centerd and lets the wall be set from shoulder to base, which is where the scrap is on a 5 L bottle with a handle recess. The cost is output, accepted because 300 bottles an hour covers a 5 L SKU.
The view strip shows everything
A clear vertical band on an opaque bottle is a mold feature, not a material one. The strip is formed by a polished insert in the cavity, cooled on its own circuit, so the polymer freezes clear against it while the rest of the wall stays opaque. It is also the most honest part of the bottle: a die line, a moisture speck or a parison fold has nowhere to hide.
| What the strip shows | Usual cause | Correction |
|---|---|---|
| Milky band | Moisture in the pellet | Dry the material, check the hopper seal |
| Straight vertical line | Mark on the mandrel or die lip | Polish or replace the damaged part |
| Wavy edge to the strip | Parison fold against the insert | Adjust parison thickness at that height |
| Strip narrower at the base | Insert running too hot | Separate cooling circuit at a lower temperature |
| Specks or bubbles | Contaminated regrind | Screen and dry the regrind before use |
One size, two machines
The 1.8 L bottle runs on two specifications: one machine carries a single head and the view-strip mold, the other two heads and a plain mold. The split is the difference between a bottle sold on what you can see and a bottle sold on price.
| Version | Per cycle | Cycle | Per hour |
|---|---|---|---|
| Single head, view strip | 2 | 15 s | 480 (calculated) |
| Two heads, plain body | 4 | 15 s | 960 |
Duplicating the strip insert across two cavities doubles the polishing and adds a second cooling circuit that has to match the first; one dull insert then spoils both bottles, so one cavity is the cheaper way to hold the standard.
Capacity, worked out
Hourly output is 3,600 divided by the cycle time in seconds, multiplied by the bottles per cycle. All figures are at 100 per cent efficiency; a real shift runs at 80–90 per cent.
| Container | Platform | Per cycle | Cycle | Per hour | Per 24 h |
|---|---|---|---|---|---|
| 5 L detergent | KSY75-J6L, 1 head | 2 | 24 s | 300 | 7,200 |
| 1.8 L with strip | KSY50-J2L, 1 head | 2 | 15 s | 480 | 11,500 |
| 1.8 L plain | KSY50-J2L, 2 heads | 4 | 15 s | 960 | 23,000 |
| 2.5 L | KSY55-J2.5L, 1 head | 2 | 17 s | 420 | 10,100 |
The 2.5 L machine fills the gap between the two ends, on the same cycle family as the 1.8 L, without borrowing the 5 L machine for a mold it was not sized for.
Line configuration
| Item | Specification |
|---|---|
| Blow molding machines | One 5 L platform, two 1.8 L platforms, one 2.5 L platform, all double station |
| Blow molds | 5 L, 1.8 L plain, 1.8 L with polished strip insert, 2.5 L |
| De-flashing | Automatic, one unit per machine, cutting at the pinch-off line |
| Leak testing | In-line pressure decay on the 5 L and 2.5 L lines |
| Chiller and granulator | Central chiller; granulator with regrind returned to each machine |
Commissioning
Each machine needs 380 V three-phase power, cooling water, 0.6–0.8 MPa compressed air and a level floor. The engineer aligns the platens, sets die head concentricity, then runs the first mold to a wall record at four points and checks the strip under a light box. Operators are trained on start-up, wall adjustment and strip inspection.
Technical points worth carrying to another project
- Cavity count follows the wall, not the volume. A heavy 5 L parison wants one head; a light 1.8 L parison carries four.
- A clear strip is a mold and cooling decision. No machine setting will polish an insert.
- Keep the neck family together. Shared necks turn a mold change into a morning instead of a week.
- Do not put every size on the largest machine. The 2.5 L platform earns its place by not disturbing the 5 L schedule.
Where to go next
- HDPE bottle machines — the 1.8 L and 2.5 L platforms in this project.
- Detergent and shampoo bottles — handles, necks and view strips in daily chemical packaging.
- Daily chemical bottle molds — polished strip inserts and handle cores.
- Wall thickness control — the four-point check used at commissioning here.
Need a machine sized for your container?
Send the container size, weight, material and the output you need. We answer with a machine proposal and a capacity calculation, not a catalogue.