INDONESIA
PETG thick-wall bottles: single head, slow cycle, controlled base
Clear PETG bottles with a heavy base, for cosmetic and personal-care packs, blown on machines built to a PETG specification rather than a general polyolefin one. What changes in the screw, the die head and the cycle when the material is an amorphous polyester, and why 25 seconds is the right answer.
Project at a glance
| Country | Indonesia |
|---|---|
| Industry | Cosmetic and personal-care packaging |
| Containers | Clear PETG bottles with a thick base, 1.8 L and 2.5 L |
| Machines | KSY45-J1.8L × 1 and KSY55-J2.5L × 2, PETG specification, hydraulic, double station |
| Cavities | One die head on two machines, two on the third; double station gives two or four bottles per cycle |
| Construction | Single layer, transparent PETG |
| Electrical | 380 V, 50 Hz, three phase |
Engineering reference. Configuration from a project our engineers worked on, restated with the equivalent current KSY models; where the original project used a single-station machine, the current KSY equivalent is double-station. Cycle times and hourly output are for reference only: the exact output depends on your container, above all its weight.

What changes when the material is PETG
PETG is an amorphous copolyester, and most of what works on an HDPE line has to be revisited. It is hygroscopic, so it goes through a desiccant dryer before it reaches the hopper; moisture left in the pellet hydrolyses in the barrel and reappears as haze, a weak weld line and a base that splits a day after filling. It is also sticky at melt temperature, so a general-purpose screw shears it and a dead spot in the die head holds it until it degrades.
The machines here were therefore built to a PETG specification: a dedicated screw, a polished die head with individually controlled zones, and hydraulic actuation that holds the clamp shut while the base cools. The table below is the comparison the specification was written from. The temperatures are typical processing windows, not set points.
| Requirement | HDPE / PP | PETG |
|---|---|---|
| Polymer structure | Semi-crystalline | Amorphous |
| Drying before use | Usually not required | Desiccant dryer, several hours |
| Screw | General purpose | Dedicated PETG screw, low compression, polished flow path |
| Melt temperature | Roughly 190–220 °C | Roughly 235–255 °C |
| Die head | Standard steel flow path | Polished, no dead spots, individually zoned |
| Regrind | High share is normal | Limited, dried and kept clean |
| What sets the cycle | Wall cooling | Base thickness and molded-in stress |
Why a thick base is a cooling problem
The body of these bottles is thin. The base is not. A heavy base gives the pack its weight in the hand and its stability on a shelf, and it is also the section that decides the cycle, because heat has to leave an 8–12 mm wall through a mold surface that only touches the outside.
Eject a bottle while that base is still soft and three things follow. It sinks as it cools on the conveyor, so the bottle no longer stands flat. The pinch-off pulls a shrink dimple that shows through a clear wall. And the base keeps molded-in stress, which later appears as stress cracking when the bottle is filled with a fragrance or an alcohol-based lotion.
That is also the argument for one head on the heavy bottle: a single parison in the center cools most evenly, and a small temperature difference in the base becomes a visible defect.
Single head, double station: where the output comes from
Hourly output is 3,600 divided by the cycle time in seconds, multiplied by the bottles per cycle.
| Configuration | Per cycle | Cycle | Per hour | Per 24 h |
|---|---|---|---|---|
| One die head, double station | 2 | 25 s | 288 | about 6,900 |
| Two die heads, double station (calculated) | 4 | 25 s | 576 | about 13,800 |
| One die head at a 30 s cycle (calculated) | 2 | 30 s | 240 | about 5,800 |
Five extra seconds of base cooling costs 17 per cent of the output, so the base insert’s cooling circuit, not the headline cycle, is where a thick-wall project is won.
Line configuration
| Item | Specification |
|---|---|
| Blow molding machine | KSY45-J1.8L, PETG screw, one die head, double station |
| Blow molding machine | KSY55-J2.5L, PETG screw, one or two die heads, double station |
| Blow molds | Thick-base bodies in polished cavities, separate base insert |
| Hopper dryer | Desiccant, one per machine, sized to the shot weight |
| De-flashing | Automatic, cutting at the pinch-off line against a vice-mold |
| Crack and leak test | In-line, pressure decay, with the probe on the base |
| Chiller | Mold water at 10–12 °C to pull heat out of the base |
Commissioning a PETG line
The buyer brings 380 V three-phase power, cooling water, 0.6–0.8 MPa compressed air and a dry-air line to the hopper. The engineer checks alignment, die head concentricity and the first parison; the die head needs a full day to soak at temperature, and the dryer has to reach its dew point before the first pellet goes in. Wall thickness is checked at four points and at the center of the base, a sample is sectioned to confirm the base, and the first bottles are filled and left a day before the crack test.
Technical points worth carrying to another project
- The material decides the machine, not the bottle size. A 1.8 L PETG bottle needs more machine specification than a 2.5 L HDPE one.
- Price the base in seconds. The base insert and its cooling circuit are cheap next to the output lost to a longer cycle.
- One head for the heavy base, two where the mold allows. Cavity count is a wall-thickness decision before it is an output decision.
Where to go next
- PETG blow molding machines — the platform family, screw and die head options for clear polyester work.
- Cosmetic bottles — how thick bases, heavy walls and clear packs are specified.
- PETG thick-wall bottles — drying, base cooling and cycle time in more detail.
- Wall thickness control — how the four-point check in this case is carried out.
Need a machine sized for your container?
Send the container size, weight, material and the output you need. We answer with a machine proposal and a capacity calculation, not a catalogue.